Print this page

Moisture Control in Basements

Written by  The U.S. Department of Energy's Office of EERE

To effectively insulate your basement for energy efficiency and to create a comfortable space, you need to properly control moisture in your basement.

Moisture Control in Basements

 

 

 

 

 

Topic Summary

Most basement water leakage results from either bulk moisture leaks or capillary action. Bulk moisture is the flow of water through holes, cracks, and other discontinuities into the home's basement walls. Capillary action occurs when water wicks into the cracks and pores of porous building materials, such as masonry blocks, concrete, or wood. These tiny cracks and pores can absorb water in any direction — even upward.

The best approaches for preventing these problems will depend on your local climate, type of insulation, and style of construction. However, the following general rules apply to most basement designs for creating a water-managed foundation system (see corresponding illustration):

  1. Diagram showing a cross-section of a water-managed basement wall   and foundation, both above- and below-grade. The rules described in the   page text are labeled here. Number 1 points to untreated wood that is   protected from earth contact. Number 2 shows a drainage pipe on the   exterior of the wall. Number 3 shows the earth sloped away from the   wall. Number 4 shows a sill gasket between the wall and the foundation.   Number 5 shows a protective membrane between the wall and the   foundation. Number 6 shows damp-proofing material on the exterior of the   below-grade foundation wall. Number 7 shows a drainage plane, or space   below grade that directs water to the foundation drain. Number 8 shows  a  round foundation drain below the drainage plane. Number 9 is beneath   the slab floor and shows a capillary break and vapor diffusion  retarder  over 4 inches of gravel.
    Keep all untreated wood materials away from earth contact.
  2. Provide drainage, such as gutters, to conduct rainwater away from the house.
  3. Slope the earth away from all sides of the house for at least 5 feet at a minimum 5% grade (3 inches in 5 feet). Establish drainage swales to direct rainwater around.
  4. Add a sill gasket to provide air sealing.
  5. Install a protective membrane, such as caulked metal flashing or EPDM-type membrane, to serve as a capillary break that reduces wicking of water up from the masonry foundation wall. This membrane can also serve as a termite shield on top of foam board insulation.
  6. Damp-proof all below-grade portions of the foundation wall and footing to prevent the wall from absorbing ground moisture by capillary action.
  7. Place a c ontinuous drainage plane over the damp-proofing or exterior insulation to channel water to the foundation drain and relieve hydrostatic pressure. Drainage plane materials include special drainage mats, high-density fiberglass insulation products, and washed gravel. All drainage planes should be protected with a filter fabric to prevent dirt from clogging the intentional gaps in the drainage material.
  8. Install a foundation drain directly below the drainage plane and beside the footing, not on top of the footing. This prevents water from flowing against the seam between the footing and the foundation wall. Surround a perforated 4-inch plastic drainpipe with gravel and wrap both with filter fabric.
  9. Underneath the basement's slab floor, install a capillary break and vapor diffusion retarder, consisting of a layer of 6- to 10-mil polyethylene over at least 4 inches of gravel.

Consult a qualified builder, basement designer, and/or insulation contractor in your area for specific basement moisture control measures concerning your climate, type of insulation, and construction style.


Article source: The U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy (EERE). For the most up-to-date information please visit the EERE website.

Images | Diagrams

tab_contribute_image

Videos

tab_contribute_video

Whitepapers

tab_contribute_whitepaper

Last modified on Mon, Oct 18, 2010
blog comments powered by Disqus